Chevrolet Kingswood (1st gen) 1959-1960

The Chevrolet Kingswood was a 4-door station wagon produced by Chevrolet in 1959 and 1960, and again from 1969 to 1972 built on the GM B Body platform.

[B]First generation (1959-1960)[/B]
The Kingswood was deliberately made to be unique: the headlights were placed as low as the law would allow, and the cats eye tail lights were unique to this model. Its flat, wing shaped tailfins were identifiable from a distance. The car was built on a 119 in (3,000 mm) wheelbase and was 211 in (5,400 mm) long, which was 11 in (280 mm) longer than the 1957 model, making the Kingswood the longest car in the low-priced range. In addition, the car was 3 in (76 mm) wider outside and had 5 in (130 mm) more width inside than it did in 1958, through the reduction of door thickness. The frame GM X frame had no side rails.

The new Kingswood was offered as a mid range full size 4-door only 9 passenger model, with rear-facing 3rd row jump-seat standard. It was positioned between the Parkwood 6-passenger and the Nomad (now Impala based), still at the top was a six-passenger car. Wagons were still classed by themselves, but had model numbers matching the car series. Chevrolet eliminated its entry-level Delray based Yeoman models and the Biscayne-based Brookwood became Chevrolet's least expensive wagon models. Brookwoods were now available in two-door or four-door body styles, both in six-passenger configuration only. The new Parkwood 6-passenger and new Kingswood 9-passenger wagons had Bel Air's model number, and as such were the middle range wagons. A variety of speed options, such as fuel injection, special cams and lowered compression, gave horsepower ratings up to 315. The Nomad was still the top Chevy wagon. A parking brake warning light was optional. Under the hood, little change took place for '59 Chevys.

Few alterations were made for 1960. The new models possessed much more restrained front end, and the cats eye lights of the 1959 model were replaced by double cone tail lights. Under the hood, things remained constant. Fuel injection was no longer available, but with the 348 cubic inch engine, a horsepower rating of 335 at 5800 rpm was now achieved. This involved the use of three double-barrel carburetors, a special cam and an 11.25:1 compression ratio, all sold as a package.

[B]Safety[/B]
Chevrolet's 1959 and '60 Kingswoods (as well as the rest of Chevy's full size line up) still featured Chevrolet's "Safety-Girder" cruciform frame introduced in '58. Similar in layout to the frame adopted for the 1957 Cadillac, it featured box-section side rails and a boxed front cross member that bowed under the engine, these "X-frames" were used on other 1958 to 1964 Chevys, as well as Cadillac. The rear was tied together by a channel-section cross member. This design was later criticized as providing less protection in the event of a side impact collision, but would persevere until 1965.

[B]Discontinuation and replacement[/B]
General Motors discontinued the Chevrolet Kingswood wagon nameplate after only two years. For 1961 they offered a third row nine-passenger option on Brookwood to fill the void. The wagon only nameplates Brookwood, Parkwood, and Nomad were gone for 1962, instead naming their station wagons after their series names: Biscayne (replacing Brookwood directly), Bel Air and Impala. The 1962-'64 Biscayne, Bel Air, and Impala wagons were very similar to Chevy's 1961 wagon models.

[SIZE="1"]Source: wikipedia[/SIZE]