What is more aerodynamic: Wide flared fenders or a wider body?

[Big time]

Let's suppose you are designing a supercar with a narrow cabin and a wide track.

What would be more aerodynamic?
A. To have a narrow body with the wheels being covered by wide fender flares. Maybe somewhat streamlined fender flares.
B. To have a wider body covering the wheels.

[NSXType-R]

Just to let you know, instead of starting multiple threads, there is a thread where you can ask all these questions.

The Technical Questions Thread - Page 81 - Ultimatecarpage.com forums

[Cyco]

A string is exactly 9 long

A very well designed set of flares has the potential to be more aero (less change in cross sectional area at the cabin), but most are not well designed.

[Badsight]

check out the box fish, you dont need a tear drop shape to have low drag

http://en.wikipedia.org/wiki/Mercedes-Benz_Bionic

a good modern example of shape optimization is the 2012 Nissan GTR. basically looks exactly the same as the 2011 model

[coolieman1220]

coefficient of drag = cross sectional area

[Big time]

A very well designed set of flares has the potential to be more aero (less change in cross sectional area at the cabin), but most are not well designed.

Please elaborate.

I don't understand how flares can provide LESS change in cross section area. If you get a narrow body and wide flares the difference in area would be larger than a wide body which has more or less a constant area.

[csl177]

Please elaborate.

I don't understand how flares can provide LESS change in cross section area. If you get a narrow body and wide flares the difference in area would be larger than a wide body which has more or less a constant area.

You asked which is more aerodynamic; simply put, the lowest CD should be most efficient... but isn't determined by frontal area alone.
It may be achieved both fendered or by complete coverage of the wheels (flares or not) but there are many other calculations required.

To wit:

CD = Coefficient of Drag is a reflection of the aerodynamic efficiency of the shape

CL = Coefficient of Lift

CS = Coefficient of Side Force

q = Dynamic Pressure in the Test Section

r = Mass Density of Air

A = Frontal Area of Vehicle

V = Velocity

Which brings us to an example of the required energy to propel an object to designed terminal velocity:

HP = (DV)/550 = (CDqAV)/550 = (CDA 1/2 r V2)V / 550 = (CDA 1/2 rV3)/ 550

Wherein

D = Drag Force

CD = Coefficient of Drag is a reflection of the aerodynamic efficiency of the shape

V = Velocity

q = Dynamic Pressure in the Test Section

A = Frontal Area of Vehicle

r = Mass Density of Air


Aerodynamic Drag:

CD: Coefficient of Drag

Invariant with velocity unless there is Reynolds Number sensitivity. The lower the CD the more efficient the shape is to the air.
With a reference frontal area of 21 ft2, a production car will have a CD around the 0.340 range

CDA: Coefficient of Drag Area

Coefficient of Drag x Area: CD x A

Reynolds Number: the ratio of inertial forces (vsρ) to viscous forces (μ/L) and consequently it quantifies the relative importance of these two types of forces for given flow conditions.

Dynamic Pressure: (PSF) A2 measures the test section speed in q which is the dynamic pressure.

q = ½ r V2

Flow Rate: (ft3/minute)

CFM = Area (ft2) x Speed (ft/min)

Source: APPENDIX

[Cyco]

Please elaborate.

I don't understand how flares can provide LESS change in cross section area. If you get a narrow body and wide flares the difference in area would be larger than a wide body which has more or less a constant area.

For a closed cockpit, i.e. Sedan/Coupe type car if the flares taper in at the front as the windscreen slopes up, and taper out at the back as the rear window tapers down then the cross section or the car has the potential to remain constant.

If, however, you have an open cockpit car eg Lotus 7, Sprite, etc running no windscreen, or only a tiny air deflector then the cockpit has no additional cross sectional area and you would be generally better off going for the wider body.

General rules of thumb only, you must measure to make sure! That is why I quoted Eggnog.